{"id":10030,"date":"2017-06-11T23:57:18","date_gmt":"2017-06-11T23:57:18","guid":{"rendered":"http:\/\/mazdaman.x10host.com\/sm355727\/"},"modified":"2017-06-11T23:57:18","modified_gmt":"2017-06-11T23:57:18","slug":"sm355727","status":"publish","type":"page","link":"https:\/\/chroot-me.in\/16ND\/sm355727\/","title":{"rendered":"DTC U3003:16 [INSTRUMENT CLUSTER]"},"content":{"rendered":"
\n <\/p>\n
\n
\n
\n < Previous<\/a> Next ><\/a><\/p>\n

2016 – MX-5 – Body and Accessories<\/h2>\n

<\/a><\/p>\n

DTC U3003:16 [INSTRUMENT CLUSTER]<\/h3>\n\n\n\n\n\n\n\n
\n

Description<\/p>\n<\/td>\n

\n

Low power supply voltage input to instrument cluster<\/p>\n<\/td>\n<\/tr>\n

\n

Detection condition<\/b><\/p>\n<\/td>\n

\n
    \n
  • \n

    Instrument cluster power supply circuit voltage of less than 10 V<\/b> is detected.<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n

\n

Fail-safe<\/b><\/p>\n<\/td>\n

\n

Not applicable<\/p>\n<\/td>\n<\/tr>\n

\n

Possible cause<\/b><\/p>\n<\/td>\n

\n
    \n
  • \n

    DTCs are stored in the PCM.<\/p>\n<\/li>\n

  • \n

    Battery malfunction<\/p>\n<\/li>\n

  • \n

    Generator malfunction<\/p>\n<\/li>\n

  • \n

    Instrument cluster connector or terminal malfunction<\/p>\n<\/li>\n

  • \n

    Instrument cluster power supply circuit malfunction<\/p>\n<\/li>\n

      \n
    • \n

      Short to ground in wiring harness between METER1 10 A fuse and instrument cluster terminal S<\/p>\n<\/li>\n

    • \n

      METER1 10 A fuse malfunction<\/p>\n<\/li>\n

    • \n

      Open circuit in wiring harness between IG1 relay terminal C and instrument cluster terminal S<\/p>\n<\/li>\n<\/ul>\n

    • \n

      Instrument cluster malfunction<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n

\n

<\/a><\/p>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n Diagnostic Procedure<\/b><\/p>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/td>\n

\n

Inspection<\/p>\n<\/td>\n

\n

Action<\/p>\n<\/td>\n<\/tr>\n

\n

1<\/p>\n<\/td>\n

\n VERIFY PCM DTCs<\/b><\/p>\n\n

Yes<\/p>\n<\/td>\n

\n

Repair or replace the malfunctioning part according to the applicable DTC troubleshooting.<\/p>\n

(See DTC TABLE [PCM (SKYACTIV-G 2.0)]<\/a>.)<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

2<\/p>\n<\/td>\n

\n INSPECT BATTERY<\/b><\/p>\n\n

Yes<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Recharge or replace the battery, then go to Step 6.<\/p>\n

(See BATTERY RECHARGING<\/a>.)<\/p>\n

(See BATTERY REMOVAL\/INSTALLATION [SKYACTIV-G 2.0]<\/a>.)<\/p>\n<\/td>\n<\/tr>\n

\n

3<\/p>\n<\/td>\n

\n INSPECT GENERATOR<\/b><\/p>\n\n

Yes<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Replace the generator, then go to Step 6.<\/p>\n

(See GENERATOR REMOVAL\/INSTALLATION [SKYACTIV-G 2.0]<\/a>.)<\/p>\n<\/td>\n<\/tr>\n

\n

4<\/p>\n<\/td>\n

\n INSPECT INSTRUMENT CLUSTER CONNECTOR CONDITION<\/b><\/p>\n\n

Yes<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Repair or replace the connector, then go to Step 6.<\/p>\n<\/td>\n<\/tr>\n

\n

5<\/p>\n<\/td>\n

\n VERIFY INSTRUMENT CLUSTER POWER SUPPLY VOLTAGE<\/b><\/p>\n\n

Yes<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Inspect the METER1 10 A fuse.<\/p>\n

    \n
  • \n

    If the fuse is blown:<\/p>\n<\/li>\n

      \n
    • \n

      Refer to the wiring diagram and verify whether or not there is a common connector between METER1 10 A fuse and instrument cluster terminal S.<\/p>\n<\/li>\n

        \n If there is a common connector:<\/b><\/p>\n
      • \n

        Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.<\/p>\n<\/li>\n

      • \n

        Repair or replace the malfunctioning part.<\/p>\n<\/li>\n<\/ul>\n

          \n If there is no common connector:<\/b><\/p>\n
        • \n

          Repair or replace the wiring harness which has a short to ground.<\/p>\n<\/li>\n

        • \n

          Replace the fuse.<\/p>\n<\/li>\n<\/ul>\n<\/ul>\n

        • \n

          If the fuse is damaged:<\/p>\n<\/li>\n

            \n
          • \n

            Replace the fuse.<\/p>\n<\/li>\n<\/ul>\n

          • \n

            If the fuse is normal:<\/p>\n<\/li>\n

              \n
            • \n

              Refer to the wiring diagram and verify whether or not there is a common connector between IG1 relay terminal C and instrument cluster terminal S.<\/p>\n<\/li>\n

                \n If there is a common connector:<\/b><\/p>\n
              • \n

                Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.<\/p>\n<\/li>\n

              • \n

                Repair or replace the malfunctioning part.<\/p>\n<\/li>\n<\/ul>\n

                  \n If there is no common connector:<\/b><\/p>\n
                • \n

                  Repair or replace the wiring harness which has an open circuit.<\/p>\n<\/li>\n<\/ul>\n<\/ul>\n<\/ul>\n

                  Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

6<\/p>\n<\/td>\n

\n VERIFY THAT REPAIRS HAVE BEEN COMPLETED<\/b><\/p>\n\n

Yes<\/p>\n<\/td>\n

\n

Repeat the inspection from Step 1.<\/p>\n

\n

No<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

7<\/p>\n<\/td>\n

\n VERIFY IF OTHER DTCs DISPLAYED<\/b><\/p>\n
    \n
  • \n

    Are any other DTCs displayed?<\/p>\n<\/li>\n<\/ul>\n<\/td>\n

\n

Yes<\/p>\n<\/td>\n

\n

Repair or replace the malfunctioning part according to the applicable DTC troubleshooting.<\/p>\n

(See DTC TABLE [INSTRUMENT CLUSTER]<\/a>.)<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

DTC troubleshooting completed.<\/p>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n < Previous<\/a> Next ><\/a><\/p>\n

\n Back to Top<\/a>\n <\/div>\n
\n \u00a9 2014 Mazda North American Operations, U.S.A.<\/em>\n <\/div>\n<\/p><\/div>\n<\/p><\/div>\n<\/p><\/div>\n<\/p><\/div>\n","protected":false},"excerpt":{"rendered":"

< Previous Next > 2016 – MX-5 – Body and Accessories DTC U3003:16 [INSTRUMENT CLUSTER] Description Low power supply voltage input to instrument cluster Detection condition Instrument cluster power supply circuit voltage of less than 10 V is detected. Fail-safe Not applicable Possible cause DTCs are stored in the PCM. Battery malfunction Generator malfunction Instrument cluster connector or terminal malfunction Instrument cluster power supply circuit malfunction Short to ground in wiring harness between METER1 10 […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"footnotes":""},"class_list":["post-10030","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/pages\/10030","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/comments?post=10030"}],"version-history":[{"count":0,"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/pages\/10030\/revisions"}],"wp:attachment":[{"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/media?parent=10030"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}