{"id":10278,"date":"2017-06-11T23:56:54","date_gmt":"2017-06-11T23:56:54","guid":{"rendered":"http:\/\/mazdaman.x10host.com\/sm355976\/"},"modified":"2017-06-11T23:56:54","modified_gmt":"2017-06-11T23:56:54","slug":"sm355976","status":"publish","type":"page","link":"https:\/\/chroot-me.in\/16ND\/sm355976\/","title":{"rendered":"ANSWER-BACK BUZZER DOES NOT SOUND [SECURITY AND LOCKS]"},"content":{"rendered":"
\n <\/p>\n
\n
\n
\n < Previous<\/a> Next ><\/a><\/p>\n

2016 – MX-5 – Body and Accessories<\/h2>\n

<\/a><\/p>\n

ANSWER-BACK BUZZER DOES NOT SOUND [SECURITY AND LOCKS]<\/h3>\n\n\n\n\n\n
\n

Description<\/b><\/p>\n<\/td>\n

\n

The keyless beeper does not sound when door lock\/unlock operation is performed using the remote transmitter button.<\/p>\n<\/td>\n<\/tr>\n

\n

Possible Causes<\/b><\/p>\n<\/td>\n

\n
    \n
  • \n

    Keyless beeper malfunction<\/p>\n<\/li>\n

  • \n

    Short to power supply in wiring harness between the following terminals:<\/p>\n<\/li>\n

      \n
    • \n

      Keyless beeper terminal A and LF control unit terminal H<\/p>\n<\/li>\n

    • \n

      Keyless beeper terminal B and LF control unit terminal J<\/p>\n<\/li>\n<\/ul>\n

    • \n

      Short to ground in wiring harness between the following terminals:<\/p>\n<\/li>\n

        \n
      • \n

        Keyless beeper terminal A and LF control unit terminal H<\/p>\n<\/li>\n

      • \n

        Keyless beeper terminal B and LF control unit terminal J<\/p>\n<\/li>\n<\/ul>\n

      • \n

        Open circuit in wiring harness between the following terminals:<\/p>\n<\/li>\n

          \n
        • \n

          Keyless beeper terminal A and LF control unit terminal H<\/p>\n<\/li>\n

        • \n

          Keyless beeper terminal B and LF control unit terminal J<\/p>\n<\/li>\n

        • \n

          Start stop unit terminal 1AF and ground<\/p>\n<\/li>\n

        • \n

          Start stop unit terminal 2A and ground<\/p>\n<\/li>\n

        • \n

          Start stop unit terminal 2B and ground<\/p>\n<\/li>\n<\/ul>\n

        • \n

          Personalization feature not set<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n

\n

<\/a><\/p>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n <\/a><\/p>\n

Diagnostic Procedure<\/h4>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/td>\n

\n

Inspection<\/p>\n<\/td>\n

\n

Action<\/p>\n<\/td>\n<\/tr>\n

\n

1<\/p>\n<\/td>\n

\n\n

Yes<\/p>\n<\/td>\n

\n

Set the volume so that the keyless beeper sounds and verify the operation.<\/p>\n

    \n Operation is verified:<\/b><\/p>\n
  • \n

    Troubleshooting completed. (Explain the servicing contents to the customer.)<\/p>\n<\/li>\n<\/ul>\n

      \n Operation is not verified:<\/b><\/p>\n
    • \n

      Go to the next step.<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

2<\/p>\n<\/td>\n

\n\n

Yes<\/p>\n<\/td>\n

\n
    \n
  • \n

    Refer to the wiring diagram and verify if there is a common connector between the following terminals.<\/p>\n<\/li>\n

      \n
    • \n

      Keyless beeper terminal A and LF control unit terminal H<\/p>\n<\/li>\n

    • \n

      Keyless beeper terminal B and LF control unit terminal J<\/p>\n<\/li>\n

        \n If there is a common connector:<\/b><\/p>\n
      • \n

        Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for an short to ground to determine the malfunctioning location.<\/p>\n<\/li>\n

      • \n

        Repair or replace the malfunctioning location.<\/p>\n<\/li>\n<\/ul>\n

          \n If there is no common connector:<\/b><\/p>\n
        • \n

          Repair or replace the wiring harness which has an short to ground.<\/p>\n<\/li>\n<\/ul>\n<\/ul>\n<\/ul>\n

            \n
          • \n

            After replacement, go to Step 6.<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

3<\/p>\n<\/td>\n

\n\n

Yes<\/p>\n<\/td>\n

\n
    \n
  • \n

    Refer to the wiring diagram and verify if there is a common connector between the following terminals.<\/p>\n<\/li>\n

      \n
    • \n

      Keyless beeper terminal A and LF control unit terminal H<\/p>\n<\/li>\n

    • \n

      Keyless beeper terminal B and LF control unit terminal J<\/p>\n<\/li>\n

        \n If there is a common connector:<\/b><\/p>\n
      • \n

        Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for an short to power supply to determine the malfunctioning location.<\/p>\n<\/li>\n

      • \n

        Repair or replace the malfunctioning location.<\/p>\n<\/li>\n<\/ul>\n

          \n If there is no common connector:<\/b><\/p>\n
        • \n

          Repair or replace the wiring harness which has an short to power supply.<\/p>\n<\/li>\n<\/ul>\n<\/ul>\n<\/ul>\n

            \n
          • \n

            After replacement, go to Step 6.<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

4<\/p>\n<\/td>\n

\n\n

Yes<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n
    \n
  • \n

    Refer to the wiring diagram and verify if there is a common connector between the following terminals.<\/p>\n<\/li>\n

      \n
    • \n

      Start stop unit terminal 1AF and ground<\/p>\n<\/li>\n

    • \n

      Start stop unit terminal 2A and ground<\/p>\n<\/li>\n

    • \n

      Start stop unit terminal 2B and ground<\/p>\n<\/li>\n

        \n If there is a common connector:<\/b><\/p>\n
      • \n

        Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for an open circuit to determine the malfunctioning location.<\/p>\n<\/li>\n

      • \n

        Repair or replace the malfunctioning location.<\/p>\n<\/li>\n<\/ul>\n

          \n If there is no common connector:<\/b><\/p>\n
        • \n

          Repair or replace the wiring harness which has an open circuit.<\/p>\n<\/li>\n<\/ul>\n<\/ul>\n<\/ul>\n

            \n
          • \n

            After replacement, go to Step 6.<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n

\n

5<\/p>\n<\/td>\n

\n
    \n INSPECT IF MALFUNCTION CAUSE IS OPEN CIRCUIT IN WIRING HARNESS BETWEEN KEYLESS BEEPER AND LF CONTROL UNIT OR KEYLESS BEEPER<\/b><\/p>\n
  • \n

    Disconnect the keyless beeper connector<\/p>\n<\/li>\n<\/ul>\n

      \n
    • \n

      Inspect for continuity between the following terminals (vehicle wiring harness).<\/p>\n<\/li>\n

        \n
      • \n

        Keyless beeper terminal A and LF control unit terminal H<\/p>\n<\/li>\n

      • \n

        Keyless beeper terminal B and LF control unit terminal J<\/p>\n<\/li>\n<\/ul>\n

      • \n

        Is there continuity?<\/p>\n<\/li>\n<\/ul>\n<\/td>\n

\n

Yes<\/p>\n<\/td>\n

\n
\n

No<\/p>\n<\/td>\n

\n
    \n
  • \n

    Refer to the wiring diagram and verify if there is a common connector between the following terminals.<\/p>\n<\/li>\n

      \n
    • \n

      Keyless beeper terminal A and LF control unit terminal H<\/p>\n<\/li>\n

    • \n

      Keyless beeper terminal B and LF control unit terminal J<\/p>\n<\/li>\n

        \n If there is a common connector:<\/b><\/p>\n
      • \n

        Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for an open circuit to determine the malfunctioning location.<\/p>\n<\/li>\n

      • \n

        Repair or replace the malfunctioning location.<\/p>\n<\/li>\n<\/ul>\n

          \n If there is no common connector:<\/b><\/p>\n
        • \n

          Repair or replace the wiring harness which has an open circuit.<\/p>\n<\/li>\n<\/ul>\n<\/ul>\n<\/ul>\n

            \n
          • \n

            After replacement, go to the next step.<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n

\n

6<\/p>\n<\/td>\n

\n
    \n VERIFY IF MALFUNCTION CAUSE WAS CORRECTED<\/b><\/p>\n
  • \n

    Does the keyless beeper sound?<\/p>\n<\/li>\n<\/ul>\n<\/td>\n

\n

Yes<\/p>\n<\/td>\n

\n

Troubleshooting completed. (Explain the contents of the servicing to the customer.)<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

If the malfunction has not been resolved, repeat the inspection from Step 1.<\/p>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n < Previous<\/a> Next ><\/a><\/p>\n

\n Back to Top<\/a>\n <\/div>\n
\n \u00a9 2014 Mazda North American Operations, U.S.A.<\/em>\n <\/div>\n<\/p><\/div>\n<\/p><\/div>\n<\/p><\/div>\n<\/p><\/div>\n","protected":false},"excerpt":{"rendered":"

< Previous Next > 2016 – MX-5 – Body and Accessories ANSWER-BACK BUZZER DOES NOT SOUND [SECURITY AND LOCKS] Description The keyless beeper does not sound when door lock\/unlock operation is performed using the remote transmitter button. Possible Causes Keyless beeper malfunction Short to power supply in wiring harness between the following terminals: Keyless beeper terminal A and LF control unit terminal H Keyless beeper terminal B and LF control unit terminal J Short to […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"footnotes":""},"class_list":["post-10278","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/pages\/10278","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/comments?post=10278"}],"version-history":[{"count":0,"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/pages\/10278\/revisions"}],"wp:attachment":[{"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/media?parent=10278"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}