{"id":8921,"date":"2017-06-11T23:58:15","date_gmt":"2017-06-11T23:58:15","guid":{"rendered":"http:\/\/mazdaman.x10host.com\/sm352588\/"},"modified":"2017-06-11T23:58:15","modified_gmt":"2017-06-11T23:58:15","slug":"sm352588","status":"publish","type":"page","link":"https:\/\/chroot-me.in\/16ND\/sm352588\/","title":{"rendered":"DTC P2127:00 [PCM (SKYACTIV-G 2.0)]"},"content":{"rendered":"<div class=\"node node SERVICE_MANUALS\">\n    <\/p>\n<div class=\"textleft\">\n<div class=\"attr CONTENT c2\">\n<div class=\"content\">\n          <link rel=\"stylesheet\" type=\"text\/css\" href=\"style.css\" media=\"screen\"><a class=\"prevPage\" href=\"SM352587\">&lt; Previous<\/a> <a class=\"nextPage\" href=\"SM352589\">Next &gt;<\/a><\/p>\n<h2>2016 &#8211; MX-5 &#8211; Engine<\/h2>\n<p><a name=\"id0102i5708500\" id=\"id0102i5708500\"><\/a><\/p>\n<h3>DTC P2127:00 [PCM (SKYACTIV-G 2.0)]<\/h3>\n<table border=\"1\" cellpadding=\"0\" cellspacing=\"@colsep\" bordercolor=\"#CCCCCC\" frame=\"box\" rules=\"all\">\n<tbody valign=\"\" cellspacing=\"1\" rowspan=\"\">\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>DTC P2127:00<\/p>\n<\/td>\n<td valign=\"middle\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>APP sensor No.2 circuit low input<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p><b>DETECTION CONDITION<\/b><\/p>\n<\/td>\n<td valign=\"middle\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<ul type=\"disc\">\n<li>\n<p>The PCM monitors the input voltage from APP sensor No.2. If the input voltage at the PCM terminal 2AS is <b>less than 0.1 V<\/b>, the PCM determines that the APP sensor No.2 circuit has a malfunction.<\/p>\n<\/li>\n<\/ul>\n<ul type=\"disc\">\n                      <b>Diagnostic support note<\/b><\/p>\n<li>\n<p>This is a continuous monitor (CCM).<\/p>\n<\/li>\n<li>\n<p>The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.<\/p>\n<\/li>\n<li>\n<p>FREEZE FRAME DATA\/Snapshot data is available.<\/p>\n<\/li>\n<li>\n<p>DTC is stored in the PCM memory.<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p><b>FAIL-SAFE FUNCTION<\/b><\/p>\n<\/td>\n<td valign=\"middle\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<ul type=\"disc\">\n<li>\n<p>Regulates the upper limit of the APP sensor output.<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p><b>POSSIBLE CAUSE<\/b><\/p>\n<\/td>\n<td valign=\"middle\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<ul type=\"disc\">\n<li>\n<p>APP sensor connector or terminals malfunction<\/p>\n<\/li>\n<li>\n<p>Short to ground in wiring harness between the following terminals:<\/p>\n<\/li>\n<ul type=\"square\">\n<li>\n<p>APP sensor terminal F\u2014PCM terminal 2AW<\/p>\n<\/li>\n<li>\n<p>APP sensor terminal E\u2014PCM terminal 2AS<\/p>\n<\/li>\n<\/ul>\n<li>\n<p>PCM connector or terminals malfunction<\/p>\n<\/li>\n<li>\n<p>APP sensor No.2 signal circuit and ground circuit are shorted to each other<\/p>\n<\/li>\n<li>\n<p>Open circuit in wiring harness between the following terminals:<\/p>\n<\/li>\n<ul type=\"square\">\n<li>\n<p>APP sensor terminal F\u2014PCM terminal 2AW<\/p>\n<\/li>\n<li>\n<p>APP sensor terminal E\u2014PCM terminal 2AS<\/p>\n<\/li>\n<\/ul>\n<li>\n<p>APP sensor No.2 malfunction<\/p>\n<\/li>\n<li>\n<p>PCM malfunction<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"2\">\n<p align=\"center\"><a href=\"\/16ND\/wp-content\/uploads\/2017\/05\/AM2ZZW00010484.GIF\"><img decoding=\"async\" align=\"absmiddle\" border=\"0\" src=\"\/16ND\/wp-content\/uploads\/2017\/05\/AM2ZZW00010484.GIF\"><\/a><\/p>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><\/p>\n<p><b><span class=\"c1\">CAUTION:<\/span><\/b><\/p>\n<ul type=\"disc\">\n<li>\n<p>Verify the malfunction symptom according to not only the PID value but also the symptom troubleshooting.<\/p>\n<\/li>\n<\/ul>\n<p>          <b>Related PIDs<\/b><\/p>\n<table border=\"1\" cellpadding=\"0\" cellspacing=\"@colsep\" bordercolor=\"#CCCCCC\" frame=\"box\" rules=\"all\">\n<tbody valign=\"\" cellspacing=\"1\" rowspan=\"\">\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Item (definition)<\/p>\n<\/td>\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Unit\/Condition<\/p>\n<\/td>\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Definition<\/p>\n<\/td>\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Condition\/Specification (Reference)<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"middle\" align=\"left\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n<p>APP1<\/p>\n<\/td>\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>%<\/p>\n<\/td>\n<td valign=\"middle\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Accelerator pedal opening angle (absolute value) input from APP sensor No.1<\/p>\n<\/td>\n<td valign=\"middle\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<ul type=\"disc\">\n<li>\n<p>Accelerator pedal released: Approx. 15.29%<\/p>\n<\/li>\n<li>\n<p>Accelerator pedal fully depressed: Approx. 90.98%<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>V<\/p>\n<\/td>\n<td valign=\"middle\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>APP sensor No.1 voltage<\/p>\n<\/td>\n<td valign=\"middle\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<ul type=\"disc\">\n<li>\n<p>Accelerator pedal released: Approx. 0.77 V<\/p>\n<\/li>\n<li>\n<p>Accelerator pedal fully depressed: Approx. 4.55 V<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"middle\" align=\"left\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n<p>APP2<\/p>\n<\/td>\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>%<\/p>\n<\/td>\n<td valign=\"middle\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Accelerator pedal opening angle (absolute value) input from APP sensor No.2<\/p>\n<\/td>\n<td valign=\"middle\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<ul type=\"disc\">\n<li>\n<p>Accelerator pedal released: Approx. 7.84%<\/p>\n<\/li>\n<li>\n<p>Accelerator pedal fully depressed: Approx. 45.49%<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>V<\/p>\n<\/td>\n<td valign=\"middle\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>APP sensor No.2 voltage<\/p>\n<\/td>\n<td valign=\"middle\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<ul type=\"disc\">\n<li>\n<p>Accelerator pedal released: Approx. 0.38 V<\/p>\n<\/li>\n<li>\n<p>Accelerator pedal fully depressed: Approx. 2.27 V<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>\n          <b>Diagnostic Procedure<\/b><\/p>\n<table border=\"1\" cellpadding=\"0\" cellspacing=\"@colsep\" bordercolor=\"#CCCCCC\" frame=\"box\" rules=\"all\">\n<tbody valign=\"\" cellspacing=\"1\" rowspan=\"\">\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>STEP<\/p>\n<\/td>\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"2\">\n<p>INSPECTION<\/p>\n<\/td>\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>ACTION<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>1<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n                  <b>RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION<\/b><\/p>\n<p><b><span class=\"c1\">NOTE:<\/span><\/b><\/p>\n<ul type=\"disc\">\n<li>\n<p>Recording can be facilitated using the screen capture function of the PC.<\/p>\n<\/li>\n<\/ul>\n<ul type=\"disc\">\n<li>\n<p>Record the FREEZE FRAME DATA\/snapshot data on the repair order.<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<td valign=\"middle\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>\u2014<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Go to the next step.<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n<p>2<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n                  <b>VERIFY RELATED REPAIR INFORMATION AVAILABILITY<\/b><\/p>\n<ul type=\"disc\">\n<li>\n<p>Verify related Service Bulletins and\/or on-line repair information availability.<\/p>\n<\/li>\n<li>\n<p>Is any related repair information available?<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Yes<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Perform repair or diagnosis according to the available repair information.<\/p>\n<ul type=\"disc\">\n<li>\n<p>If the vehicle is not repaired, go to the next step.<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>No<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Go to the next step.<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n<p>3<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n                  <b>INSPECT APP SENSOR CONNECTOR CONDITION<\/b><\/p>\n<ul type=\"disc\">\n<li>\n<p>Switch the ignition off.<\/p>\n<\/li>\n<li>\n<p>Disconnect the APP sensor connector.<\/p>\n<\/li>\n<li>\n<p>Inspect for poor connection (such as damaged\/pulled-out pins, corrosion).<\/p>\n<\/li>\n<li>\n<p>Is there any malfunction?<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Yes<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Repair or replace the connector and\/or terminals, then go to Step 9.<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>No<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Go to the next step.<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n<p>4<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n                  <b>INSPECT APP SENSOR NO.2 CIRCUIT FOR SHORT TO GROUND<\/b><\/p>\n<ul type=\"disc\">\n<li>\n<p>Verify that the APP sensor connector is disconnected.<\/p>\n<\/li>\n<li>\n<p>Inspect for continuity between the following terminals (wiring harness-side) and body ground:<\/p>\n<\/li>\n<ul type=\"square\">\n<li>\n<p>APP sensor terminal F<\/p>\n<\/li>\n<li>\n<p>APP sensor terminal E<\/p>\n<\/li>\n<\/ul>\n<li>\n<p>Is there continuity?<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Yes<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Disconnect the PCM connector and inspect the wiring harness for short to ground.<\/p>\n<ul type=\"disc\">\n<li>\n<p>If the short to ground circuit could be detected in the wiring harness:<\/p>\n<\/li>\n<ul type=\"square\">\n<li>\n<p>Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:<\/p>\n<\/li>\n<ul type=\"disc\">\n<li>\n<p>APP sensor terminal F\u2014PCM terminal 2AW<\/p>\n<\/li>\n<li>\n<p>APP sensor terminal E\u2014PCM terminal 2AS<\/p>\n<\/li>\n<\/ul>\n<ul type=\"disc\">\n                              <b>If there is a common connector:<\/b><\/p>\n<li>\n<p>Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.<\/p>\n<\/li>\n<li>\n<p>Repair or replace the malfunctioning part.<\/p>\n<\/li>\n<\/ul>\n<ul type=\"disc\">\n                              <b>If there is no common connector:<\/b><\/p>\n<li>\n<p>Repair or replace the wiring harness which has a short to ground.<\/p>\n<\/li>\n<\/ul>\n<\/ul>\n<\/ul>\n<ul type=\"disc\">\n<li>\n<p>If the short to ground circuit could not be detected in the wiring harness:<\/p>\n<\/li>\n<ul type=\"square\">\n<li>\n<p>Replace the PCM (short to ground in the PCM internal circuit).<\/p>\n<p>(See <a href=\"SM352816\">PCM REMOVAL\/INSTALLATION [SKYACTIV-G 2.0]<\/a>.)<\/p>\n<\/li>\n<\/ul>\n<\/ul>\n<p>Go to Step 9.<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>No<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Go to the next step.<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n<p>5<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n                  <b>INSPECT PCM CONNECTOR CONDITION<\/b><\/p>\n<ul type=\"disc\">\n<li>\n<p>Disconnect the PCM connector.<\/p>\n<\/li>\n<li>\n<p>Inspect for poor connection (such as damaged\/pulled-out pins, corrosion).<\/p>\n<\/li>\n<li>\n<p>Is there any malfunction?<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Yes<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Repair or replace the connector and\/or terminals, then go to Step 9.<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>No<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Go to the next step.<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n<p>6<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n                  <b>INSPECT APP SENSOR NO.2 SIGNAL CIRCUIT AND GROUND CIRCUIT FOR SHORT TO EACH OTHER<\/b><\/p>\n<ul type=\"disc\">\n<li>\n<p>Verify that the APP sensor and PCM connectors are disconnected.<\/p>\n<\/li>\n<li>\n<p>Inspect for continuity between APP sensor terminals E and D (wiring harness-side).<\/p>\n<\/li>\n<li>\n<p>Is there continuity?<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Yes<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:<\/p>\n<ul type=\"disc\">\n<li>\n<p>APP sensor terminal E\u2014PCM terminal 2AS<\/p>\n<\/li>\n<li>\n<p>APP sensor terminal D\u2014PCM terminal 2AT<\/p>\n<\/li>\n<\/ul>\n<ul type=\"disc\">\n                      <b>If there is a common connector:<\/b><\/p>\n<li>\n<p>Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to each other.<\/p>\n<\/li>\n<li>\n<p>Repair or replace the malfunctioning part.<\/p>\n<\/li>\n<\/ul>\n<ul type=\"disc\">\n                      <b>If there is no common connector:<\/b><\/p>\n<li>\n<p>Repair or replace the wiring harness which has a short to each other.<\/p>\n<\/li>\n<\/ul>\n<p>Go to Step 9.<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>No<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Go to the next step.<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n<p>7<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n                  <b>INSPECT APP SENSOR NO.2 CIRCUIT FOR OPEN CIRCUIT<\/b><\/p>\n<ul type=\"disc\">\n<li>\n<p>Verify that the APP sensor and PCM connectors are disconnected.<\/p>\n<\/li>\n<li>\n<p>Inspect for continuity between the following terminals (wiring harness-side):<\/p>\n<\/li>\n<ul type=\"square\">\n<li>\n<p>APP sensor terminal F\u2014PCM terminal 2AW<\/p>\n<\/li>\n<li>\n<p>APP sensor terminal E\u2014PCM terminal 2AS<\/p>\n<\/li>\n<\/ul>\n<li>\n<p>Is there continuity?<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Yes<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Go to the next step.<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>No<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:<\/p>\n<ul type=\"disc\">\n<li>\n<p>APP sensor terminal F\u2014PCM terminal 2AW<\/p>\n<\/li>\n<li>\n<p>APP sensor terminal E\u2014PCM terminal 2AS<\/p>\n<\/li>\n<\/ul>\n<ul type=\"disc\">\n                      <b>If there is a common connector:<\/b><\/p>\n<li>\n<p>Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.<\/p>\n<\/li>\n<li>\n<p>Repair or replace the malfunctioning part.<\/p>\n<\/li>\n<\/ul>\n<ul type=\"disc\">\n                      <b>If there is no common connector:<\/b><\/p>\n<li>\n<p>Repair or replace the wiring harness which has an open circuit.<\/p>\n<\/li>\n<\/ul>\n<p>Go to Step 9.<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n<p>8<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n                  <b>INSPECT APP SENSOR NO.2<\/b><\/p>\n<ul type=\"disc\">\n<li>\n<p>Reconnect all disconnected connectors.<\/p>\n<\/li>\n<li>\n<p>Inspect the APP sensor No.2.<\/p>\n<p>(See <a href=\"SM352821\">ACCELERATOR PEDAL POSITION (APP) SENSOR INSPECTION [SKYACTIV-G 2.0]<\/a>.)<\/p>\n<\/li>\n<li>\n<p>Is there any malfunction?<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Yes<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Replace the accelerator pedal, then go to the next step.<\/p>\n<p>(See <a href=\"SM352725\">ACCELERATOR PEDAL REMOVAL\/INSTALLATION [SKYACTIV-G 2.0]<\/a>.)<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>No<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Go to the next step.<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n<p>9<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n                  <b>VERIFY DTC TROUBLESHOOTING COMPLETED<\/b><\/p>\n<ul type=\"disc\">\n<li>\n<p>Always reconnect all disconnected connectors.<\/p>\n<\/li>\n<li>\n<p>Clear the DTC from the PCM memory using the M-MDS.<\/p>\n<p>(See <a href=\"SM352609\">AFTER REPAIR PROCEDURE [PCM (SKYACTIV-G 2.0)]<\/a>.)<\/p>\n<\/li>\n<li>\n<p>Perform the KOEO or KOER self test.<\/p>\n<p>(See <a href=\"SM352610\">KOEO\/KOER SELF TEST [PCM (SKYACTIV-G 2.0)]<\/a>.)<\/p>\n<\/li>\n<li>\n<p>Is the same DTC present?<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Yes<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Repeat the inspection from Step 1.<\/p>\n<ul type=\"disc\">\n<li>\n<p>If the malfunction recurs, replace the PCM.<\/p>\n<p>(See <a href=\"SM352816\">PCM REMOVAL\/INSTALLATION [SKYACTIV-G 2.0]<\/a>.)<\/p>\n<\/li>\n<\/ul>\n<p>Go to the next step.<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>No<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Go to the next step.<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n<p>10<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"2\" colspan=\"NaN\">\n                  <b>VERIFY AFTER REPAIR PROCEDURE<\/b><\/p>\n<ul type=\"disc\">\n<li>\n<p>Perform the \u201cAFTER REPAIR PROCEDURE\u201d.<\/p>\n<p>(See <a href=\"SM352609\">AFTER REPAIR PROCEDURE [PCM (SKYACTIV-G 2.0)]<\/a>.)<\/p>\n<\/li>\n<li>\n<p>Are any DTCs present?<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Yes<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>Go to the applicable DTC inspection.<\/p>\n<p>(See <a href=\"SM352613\">DTC TABLE [PCM (SKYACTIV-G 2.0)]<\/a>.)<\/p>\n<\/td>\n<\/tr>\n<tr valign=\"\" align=\"\" cellspacing=\"\" rowspan=\"\">\n<td valign=\"top\" align=\"center\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>No<\/p>\n<\/td>\n<td valign=\"top\" align=\"left\" cellspacing=\"\" rowspan=\"\" colspan=\"NaN\">\n<p>DTC troubleshooting completed.<\/p>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>\n          <a class=\"prevPage\" href=\"SM352587\">&lt; Previous<\/a> <a class=\"nextPage\" href=\"SM352589\">Next &gt;<\/a><\/p>\n<div align=\"right\">\n            <a href=\"\"#\">Back to Top<\/a>\n          <\/div>\n<div align=\"center\">\n            <em>\u00a9 2014 Mazda North American Operations, U.S.A.<\/em>\n          <\/div>\n<\/p><\/div>\n<\/p><\/div>\n<\/p><\/div>\n<\/p><\/div>\n","protected":false},"excerpt":{"rendered":"<p>&lt; Previous Next &gt; 2016 &#8211; MX-5 &#8211; Engine DTC P2127:00 [PCM (SKYACTIV-G 2.0)] DTC P2127:00 APP sensor No.2 circuit low input DETECTION CONDITION The PCM monitors the input voltage from APP sensor No.2. If the input voltage at the PCM terminal 2AS is less than 0.1 V, the PCM determines that the APP sensor No.2 circuit has a malfunction. Diagnostic support note This is a continuous monitor (CCM). The check engine light illuminates if [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"footnotes":""},"class_list":["post-8921","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/pages\/8921","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/comments?post=8921"}],"version-history":[{"count":0,"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/pages\/8921\/revisions"}],"wp:attachment":[{"href":"https:\/\/chroot-me.in\/16ND\/wp-json\/wp\/v2\/media?parent=8921"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}