DTC C0061:28/C0061:64/C0062:28/C0062:64/C0063:28/C0063:64 [DSC HU/CM]

id040262180800

DTC

C0061:28

SAS control module

C0061:64

C0062:28

C0062:64

C0063:28

C0063:64

DETECTION CONDITION

Note

•  The low-G sensor and the yaw rate sensor are built into the SAS control module

•  C0061:28, C0061:64

―  Out-of-specification signal modulation or lateral-G value is detected from the low-G sensor

•  C0062:28, C0062:64

―  Out-of-specification signal modulation or longitudinal-G value is detected from the low-G sensor

•  C0063:28, C0063:64

―  Out-of-specification signal modulation or yaw rate value is detected from the yaw rate sensor

FAIL-SAFE FUNCTION

Refer to DTC TABLE. (See DTC TABLE [DSC HU/CM].)

POSSIBLE CAUSE

•  SAS control module malfunction

•  DSC HU/CM malfunction

SYSTEM WIRING DIAGRAM

—

Diagnostic Procedure

Step

Inspection

Action

1

VERIFY SAS CONTROL MODULE DTC

•  Using the M-MDS, perform the SAS control module DTC inspection.
(See DTC INSPECTION [STANDARD DEPLOYMENT CONTROL SYSTEM].)

(See DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM].)

•  Are any DTCs present?

Yes

Go to applicable DTC inspection.

(See DTC TABLE [STANDARD DEPLOYMENT CONTROL SYSTEM].)

(See DTC TABLE [TWO-STEP DEPLOYMENT CONTROL SYSTEM].)

DTC troubleshooting completed, then go to the next step.

No

Go to the next step.

2

VERIFY DTC TROUBLESHOOTING COMPLETED

•  Using the M-MDS, clear the DTC from the DSC HU/CM.
(See CLEARING DTC [DSC HU/CM].)

•  Start the engine and drive the vehicle at 10 km/h {6.2 mph} or more.

•  Using the M-MDS, perform the DSC HU/CM DTC inspection.
(See DTC INSPECTION [DSC HU/CM].)

•  Is the same DTC present?

Yes

Repeat the inspection from Step1

If the malfunction recurs, replace the DSC HU/CM, then go to the next step.

(See DSC HU/CM REMOVAL/INSTALLATION [L.H.D.].)

(See DSC HU/CM REMOVAL/INSTALLATION [R.H.D.].)

No

Go to the next step.

3

VERIFY NO DTC IS PRESENT

•  Are any DTCs present?

Yes

Go to applicable DTC inspection.

(See DTC TABLE [DSC HU/CM].)

No

DTC troubleshooting completed.

DTC	C0061:28	SAS control module
	C0061:64
	C0062:28
	C0062:64
	C0063:28
	C0063:64
DETECTION CONDITION		Note • The low-G sensor and the yaw rate sensor are built into the SAS control module • C0061:28, C0061:64 ― Out-of-specification signal modulation or lateral-G value is detected from the low-G sensor • C0062:28, C0062:64 ― Out-of-specification signal modulation or longitudinal-G value is detected from the low-G sensor • C0063:28, C0063:64 ― Out-of-specification signal modulation or yaw rate value is detected from the yaw rate sensor
FAIL-SAFE FUNCTION		Refer to DTC TABLE. (See DTC TABLE [DSC HU/CM].)
POSSIBLE CAUSE		• SAS control module malfunction • DSC HU/CM malfunction
SYSTEM WIRING DIAGRAM		—

Step	Inspection		Action
1	VERIFY SAS CONTROL MODULE DTC • Using the M-MDS, perform the SAS control module DTC inspection. (See DTC INSPECTION [STANDARD DEPLOYMENT CONTROL SYSTEM].) (See DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM].) • Are any DTCs present?	Yes	Go to applicable DTC inspection. (See DTC TABLE [STANDARD DEPLOYMENT CONTROL SYSTEM].) (See DTC TABLE [TWO-STEP DEPLOYMENT CONTROL SYSTEM].) DTC troubleshooting completed, then go to the next step.
1		No	Go to the next step.
2	VERIFY DTC TROUBLESHOOTING COMPLETED • Using the M-MDS, clear the DTC from the DSC HU/CM. (See CLEARING DTC [DSC HU/CM].) • Start the engine and drive the vehicle at 10 km/h {6.2 mph} or more. • Using the M-MDS, perform the DSC HU/CM DTC inspection. (See DTC INSPECTION [DSC HU/CM].) • Is the same DTC present?	Yes	Repeat the inspection from Step1 If the malfunction recurs, replace the DSC HU/CM, then go to the next step. (See DSC HU/CM REMOVAL/INSTALLATION [L.H.D.].) (See DSC HU/CM REMOVAL/INSTALLATION [R.H.D.].)
2		No	Go to the next step.
3	VERIFY NO DTC IS PRESENT • Are any DTCs present?	Yes	Go to applicable DTC inspection. (See DTC TABLE [DSC HU/CM].)
3	VERIFY NO DTC IS PRESENT • Are any DTCs present?	No	DTC troubleshooting completed.