DTC C0061:54/C0062:54/C0063:54 [DSC HU/CM]

id040262901200

DTC

C0061:54

DSC HU/CM (unperformed initialization procedure)

C0062:54

C0063:54

DETECTION CONDITION

•  C0061:54, C0062:54

―  DSC HU/CM detects that the initialization procedure has not been performed

•  C0063:54

―  DSC HU/CM detects that the initialization procedure has not been performed

FAIL-SAFE FUNCTION

Refer to DTC TABLE. (See DTC TABLE [DSC HU/CM].)

POSSIBLE CAUSE

•  Initialization procedure for the DSC related parts sensor not performed

―  Low-G sensor

―  Yaw rate sensor

•  SAS control module malfunction

•  DSC HU/CM malfunction

SYSTEM WIRING DIAGRAM

—

Diagnostic Procedure

Step

Inspection

Action

1

VERIFY INITIALIZATION PROCEDURE

•  Was the following DSC related parts sensor initialization procedure performed?

―  Lateral acceleration sensor (low-G sensor)

―  Longitudinal acceleration sensor (low-G sensor)

―  Yaw rate sensor

Yes

Go to the next step.

No

Perform the DSC related parts sensor initialization procedure, then go to Step3.

(See DSC RELATED PARTS SENSOR INITIALIZATION PROCEDURE.)

2

VERIFY SAS CONTROL MODULE DTC

•  Using the M-MDS, perform the SAS control module DTC inspection.
(See DTC INSPECTION [STANDARD DEPLOYMENT CONTROL SYSTEM].)

(See DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM].)

•  Are any DTCs present?

Yes

Go to applicable DTC inspection.

(See DTC TABLE [STANDARD DEPLOYMENT CONTROL SYSTEM].)

(See DTC TABLE [TWO-STEP DEPLOYMENT CONTROL SYSTEM].)

DTC troubleshooting completed, then go to the next step.

No

Go to the next step.

3

VERIFY DTC TROUBLESHOOTING COMPLETED

•  Using the M-MDS, clear the DTC from the DSC HU/CM.
(See CLEARING DTC [DSC HU/CM].)

•  Using the M-MDS, perform the DSC HU/CM DTC inspection.
(See DTC INSPECTION [DSC HU/CM].)

•  Is the same DTC present?

Yes

Repeat the inspection from Step1

If the malfunction recurs, replace the DSC HU/CM, then go to the next step.

(See DSC HU/CM REMOVAL/INSTALLATION [L.H.D.].)

(See DSC HU/CM REMOVAL/INSTALLATION [R.H.D.].)

No

Go to the next step.

4

VERIFY NO DTC IS PRESENT

•  Are any DTCs present?

Yes

Go to applicable DTC inspection.

(See DTC TABLE [DSC HU/CM].)

No

DTC troubleshooting completed.

DTC	C0061:54	DSC HU/CM (unperformed initialization procedure)
	C0062:54
	C0063:54
DETECTION CONDITION		• C0061:54, C0062:54 ― DSC HU/CM detects that the initialization procedure has not been performed • C0063:54 ― DSC HU/CM detects that the initialization procedure has not been performed
FAIL-SAFE FUNCTION		Refer to DTC TABLE. (See DTC TABLE [DSC HU/CM].)
POSSIBLE CAUSE		• Initialization procedure for the DSC related parts sensor not performed ― Low-G sensor ― Yaw rate sensor • SAS control module malfunction • DSC HU/CM malfunction
SYSTEM WIRING DIAGRAM		—

Step	Inspection		Action
1	VERIFY INITIALIZATION PROCEDURE • Was the following DSC related parts sensor initialization procedure performed? ― Lateral acceleration sensor (low-G sensor) ― Longitudinal acceleration sensor (low-G sensor) ― Yaw rate sensor	Yes	Go to the next step.
1		No	Perform the DSC related parts sensor initialization procedure, then go to Step3. (See DSC RELATED PARTS SENSOR INITIALIZATION PROCEDURE.)
2	VERIFY SAS CONTROL MODULE DTC • Using the M-MDS, perform the SAS control module DTC inspection. (See DTC INSPECTION [STANDARD DEPLOYMENT CONTROL SYSTEM].) (See DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM].) • Are any DTCs present?	Yes	Go to applicable DTC inspection. (See DTC TABLE [STANDARD DEPLOYMENT CONTROL SYSTEM].) (See DTC TABLE [TWO-STEP DEPLOYMENT CONTROL SYSTEM].) DTC troubleshooting completed, then go to the next step.
2		No	Go to the next step.
3	VERIFY DTC TROUBLESHOOTING COMPLETED • Using the M-MDS, clear the DTC from the DSC HU/CM. (See CLEARING DTC [DSC HU/CM].) • Using the M-MDS, perform the DSC HU/CM DTC inspection. (See DTC INSPECTION [DSC HU/CM].) • Is the same DTC present?	Yes	Repeat the inspection from Step1 If the malfunction recurs, replace the DSC HU/CM, then go to the next step. (See DSC HU/CM REMOVAL/INSTALLATION [L.H.D.].) (See DSC HU/CM REMOVAL/INSTALLATION [R.H.D.].)
3		No	Go to the next step.
4	VERIFY NO DTC IS PRESENT • Are any DTCs present?	Yes	Go to applicable DTC inspection. (See DTC TABLE [DSC HU/CM].)
4	VERIFY NO DTC IS PRESENT • Are any DTCs present?	No	DTC troubleshooting completed.