DTC B00B5:55 [TWO-STEP DEPLOYMENT CONTROL SYSTEM]

id0802b2826500

System malfunction location

•  Configuration setting error (seat track position sensor structural malfunction)

Detection condition

Warning

•  Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When performing an inspection, always follow the inspection procedure.

•  SAS control module configuration setting has not been done correctly

•  Parts which have not been set to SAS control module are assembled

Fail-safe function

Not applicable

Possible cause

•  SAS control module configuration setting not implemented

•  SAS control module configuration setting invalid

•  Seat track position sensor assembly incorrect

•  SAS control module malfunction

System wiring diagram

Not applicable

System malfunction location	• Configuration setting error (seat track position sensor structural malfunction)
Detection condition	Warning • Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When performing an inspection, always follow the inspection procedure. • SAS control module configuration setting has not been done correctly • Parts which have not been set to SAS control module are assembled
Fail-safe function	Not applicable
Possible cause	• SAS control module configuration setting not implemented • SAS control module configuration setting invalid • Seat track position sensor assembly incorrect • SAS control module malfunction
System wiring diagram	Not applicable

Diagnostic Procedure

Step

Inspection

Action

1

PERFORM SAS CONTROL MODULE INSPECTION

•  Perform the SAS control module configuration using the M-MDS. (See SAS CONTROL MODULE CONFIGURATION (USING AS-BUILT DATA) [TWO-STEP DEPLOYMENT CONTROL SYSTEM].)

•  Switch the ignition off.

•  Switch the ignition ON (engine off or on).

•  Clear the DTC using the M-MDS. (See CLEARING DTC [TWO-STEP DEPLOYMENT CONTROL SYSTEM].)

•  Perform the DTC inspection for the SAS control module using the M-MDS. (See DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM].)

•  Is the same DTC present?

Yes

Go to the next step.

No

DTC troubleshooting completed.

2

INSPECT SEAT TRACK POSITION SENSOR

•  Verify that the seat track position sensor is correctly installed.

•  Is the seat track position sensor correctly installed?

Yes

Go to the next step.

No

Correctly install the seat track position sensor.

Then go to the next step.

3

PERFORM SAS CONTROL MODULE DTC INSPECTION

•  Clear the DTC for the SAS control module using the M-MDS. (See CLEARING DTC [TWO-STEP DEPLOYMENT CONTROL SYSTEM].)

•  Perform the DTC inspection for SAS control module using the M-MDS. (See DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM].)

•  Is the same DTC present?

Yes

Replace the SAS control module.

(See SAS CONTROL MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM].)

No

DTC troubleshooting completed.

Step	Inspection		Action
1	PERFORM SAS CONTROL MODULE INSPECTION • Perform the SAS control module configuration using the M-MDS. (See SAS CONTROL MODULE CONFIGURATION (USING AS-BUILT DATA) [TWO-STEP DEPLOYMENT CONTROL SYSTEM].) • Switch the ignition off. • Switch the ignition ON (engine off or on). • Clear the DTC using the M-MDS. (See CLEARING DTC [TWO-STEP DEPLOYMENT CONTROL SYSTEM].) • Perform the DTC inspection for the SAS control module using the M-MDS. (See DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM].) • Is the same DTC present?	Yes	Go to the next step.
1		No	DTC troubleshooting completed.
2	INSPECT SEAT TRACK POSITION SENSOR • Verify that the seat track position sensor is correctly installed. • Is the seat track position sensor correctly installed?	Yes	Go to the next step.
2		No	Correctly install the seat track position sensor. Then go to the next step.
3	PERFORM SAS CONTROL MODULE DTC INSPECTION • Clear the DTC for the SAS control module using the M-MDS. (See CLEARING DTC [TWO-STEP DEPLOYMENT CONTROL SYSTEM].) • Perform the DTC inspection for SAS control module using the M-MDS. (See DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM].) • Is the same DTC present?	Yes	Replace the SAS control module. (See SAS CONTROL MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM].)
3		No	DTC troubleshooting completed.