DTC B1238:01 [CONNECTIVITY MASTER UNIT]

id0902n7104800

Description

Speaker circuit malfunction
Detection condition
•  The connectivity master unit (CMU) detected a short to ground or short to power supply in the speaker circuit with the ignition switched ON (engine off or on).
Fail-safe
Not applicable
Possible cause
•  Tuner and amp unit (TAU) connector or terminal malfunction
•  Front door speaker (LH) connector or terminal malfunction
•  Tweeter (LH) connector or terminal malfunction
•  Short to ground in wiring harness between the following terminals:
―  Tuner and amp unit (TAU) terminal 2A and front door speaker (LH) terminal C
―  Tuner and amp unit (TAU) terminal 2C and front door speaker (LH) terminal B
―  Tuner and amp unit (TAU) terminal 2A and tweeter (LH) terminal B
―  Tuner and amp unit (TAU) terminal 2C and tweeter (LH) terminal A
•  Short to power supply in wiring harness between the following terminals:
―  Tuner and amp unit (TAU) terminal 2A and front door speaker (LH) terminal C
―  Tuner and amp unit (TAU) terminal 2C and front door speaker (LH) terminal B
―  Tuner and amp unit (TAU) terminal 2A and tweeter (LH) terminal B
―  Tuner and amp unit (TAU) terminal 2C and tweeter (LH) terminal A
•  Front door speaker (LH) malfunction
•  Tweeter (LH) malfunction
•  Front door speaker (RH) connector or terminal malfunction
•  Tweeter (RH) connector or terminal malfunction
•  Short to ground in wiring harness between the following terminals:
―  Tuner and amp unit (TAU) terminal 2D and front door speaker (RH) terminal C
―  Tuner and amp unit (TAU) terminal 2F and front door speaker (RH) terminal B
―  Tuner and amp unit (TAU) terminal 2D and tweeter (RH) terminal B
―  Tuner and amp unit (TAU) terminal 2F and tweeter (RH) terminal A
•  Short to power supply in wiring harness between the following terminals:
―  Tuner and amp unit (TAU) terminal 2D and front door speaker (RH) terminal C
―  Tuner and amp unit (TAU) terminal 2F and front door speaker (RH) terminal B
―  Tuner and amp unit (TAU) terminal 2D and tweeter (RH) terminal B
―  Tuner and amp unit (TAU) terminal 2F and tweeter (RH) terminal A
•  Front door speaker (RH) malfunction
•  Tweeter (RH) malfunction
•  Rear door speaker (LH) connector or terminal malfunction
•  Short to ground in wiring harness between the following terminals:
―  Tuner and amp unit (TAU) terminal 2S and rear door speaker (LH) terminal C
―  Tuner and amp unit (TAU) terminal 2U and rear door speaker (LH) terminal B
•  Short to power supply in wiring harness between the following terminals:
―  Tuner and amp unit (TAU) terminal 2S and rear door speaker (LH) terminal C
―  Tuner and amp unit (TAU) terminal 2U and rear door speaker (LH) terminal B
•  Rear door speaker (LH) malfunction
•  Rear door speaker (RH) connector or terminal malfunction
•  Short to ground in wiring harness between the following terminals:
―  Tuner and amp unit (TAU) terminal 2V and rear door speaker (RH) terminal C
―  Tuner and amp unit (TAU) terminal 2X and rear door speaker (RH) terminal B
•  Short to power supply in wiring harness between the following terminals:
―  Tuner and amp unit (TAU) terminal 2V and rear door speaker (RH) terminal C
―  Tuner and amp unit (TAU) terminal 2X and rear door speaker (RH) terminal B
•  Rear door speaker (RH) malfunction
•  Tuner and amp unit (TAU) malfunction

Diagnostic Procedure

Step

Inspection

Action
1
DETERMINE MALFUNCTIONING SPEAKER
•  Perform diagnostic assist code “94” speaker inspection.
•  Is audio produced from each speaker in order?
Yes
Go to Step 27.
No
No audio produced from front door speaker (LH) and tweeter (LH)
•  Go to the next step.
No audio produced from front door speaker (RH) and tweeter (RH)
•  Go to Step 9.
No sound produced from rear door speaker (LH)
•  Go to Step 16.
No audio produced from rear door speaker (RH)
•  Go to Step 21.
No audio produced from all speakers.
•  Go to Step 26.
2
INSPECT TUNER AND AMP UNIT (TAU) CONNECTOR CONDITION
•  Switch the ignition off.
•  Disconnect the negative battery cable.
•  Disconnect the tuner and amp unit (TAU) connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 27.
3
INSPECT FRONT DOOR SPEAKER (LH) CONNECTOR CONDITION
•  Disconnect the front door speaker (LH) connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 27.
4
INSPECT TWEETER (LH) CONNECTOR CONDITION
•  Disconnect the tweeter (LH) connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 27.
5
INSPECT FRONT DOOR SPEAKER (LH) CIRCUIT FOR SHORT TO GROUND
•  Verify that the following connectors are disconnected.
―  Tuner and amp unit (TAU)
―  Front door speaker (LH)
―  Tweeter (LH)
•  Inspect for continuity between the following terminals (wiring harness-side) and body ground.
―  Front door speaker (LH) terminal C
―  Front door speaker (LH) terminal B
•  Is there continuity?
Yes
Refer to the wiring diagram and verify if there is a common connector between the following terminals.
•  Tuner and amp unit (TAU) terminal 2A and front door speaker (LH) terminal C
•  Tuner and amp unit (TAU) terminal 2C and front door speaker (LH) terminal B
•  Tuner and amp unit (TAU) terminal 2A and tweeter (LH) terminal B
•  Tuner and amp unit (TAU) terminal 2C and tweeter (LH) terminal A
If there is a common connector:
•  Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for short to ground to determine the malfunctioning location.
•  Repair or replace the malfunctioning location.
If there is no common connector:
•  Repair or replace the wiring harness which is shorted to ground.
Go to Step 27.
No
Go to the next step.
6
INSPECT FRONT DOOR SPEAKER (LH) CIRCUIT FOR SHORT TO POWER SUPPLY
•  Verify that the following connectors are disconnected.
―  Tuner and amp unit (TAU)
―  Front door speaker (LH)
―  Tweeter (LH)
•  Connect the negative battery cable.
•  Switch the ignition ON (engine off or on).
•  Measure the voltage at the following terminals (wiring harness-side).
―  Front door speaker (LH) terminal C
―  Front door speaker (LH) terminal B
•  Is the voltage 0 V?
Yes
Go to the next step.
No
Refer to the wiring diagram and verify if there is a common connector between the following terminals.
•  Tuner and amp unit (TAU) terminal 2A and front door speaker (LH) terminal C
•  Tuner and amp unit (TAU) terminal 2C and front door speaker (LH) terminal B
•  Tuner and amp unit (TAU) terminal 2A and tweeter (LH) terminal B
•  Tuner and amp unit (TAU) terminal 2C and tweeter (LH) terminal A
If there is a common connector:
•  Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for short to power supply to determine the malfunctioning location.
•  Repair or replace the malfunctioning location.
If there is no common connector:
•  Repair or replace the wiring harness which is shorted to the power supply.
Go to Step 27.
7
INSPECT FRONT DOOR SPEAKER (LH)
•  Inspect the front door speaker (LH).
•  Is the front door speaker (LH) normal?
Yes
Go to the next step.
No
Replace the front door speaker (LH), then go to Step 27.
(See FRONT DOOR SPEAKER REMOVAL/INSTALLATION.)
8
INSPECT TWEETER (LH)
•  Inspect the tweeter (LH)
•  Is the tweeter (LH) normal?
Yes
Go to Step 27.
No
Replace the tweeter (LH), then go to Step 27.
(See TWEETER REMOVAL/INSTALLATION.)
9
INSPECT TUNER AND AMP UNIT (TAU) CONNECTOR CONDITION
•  Switch the ignition off.
•  Disconnect the negative battery cable.
•  Disconnect the tuner and amp unit (TAU) connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 27.
10
INSPECT FRONT DOOR SPEAKER (RH) CONNECTOR CONDITION
•  Disconnect the front door speaker (RH) connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 27.
11
INSPECT TWEETER (RH) CONNECTOR CONDITION
•  Disconnect the tweeter (RH) connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 27.
12
INSPECT FRONT DOOR SPEAKER (RH) CIRCUIT FOR SHORT TO GROUND
•  Verify that the following connectors are disconnected.
―  Tuner and amp unit (TAU)
―  Front door speaker (RH)
―  Tweeter (RH)
•  Inspect for continuity between the following terminals (wiring harness-side) and body ground.
―  Front door speaker (RH) terminal C
―  Front door speaker (RH) terminal B
•  Is there continuity?
Yes
Refer to the wiring diagram and verify if there is a common connector between the following terminals.
•  Tuner and amp unit (TAU) terminal 2D and front door speaker (RH) terminal C
•  Tuner and amp unit (TAU) terminal 2F and front door speaker (RH) terminal B
•  Tuner and amp unit (TAU) terminal 2D and tweeter (RH) terminal B
•  Tuner and amp unit (TAU) terminal 2F and tweeter (RH) terminal A
If there is a common connector:
•  Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for short to ground to determine the malfunctioning location.
•  Repair or replace the malfunctioning location.
If there is no common connector:
•  Repair or replace the wiring harness which is shorted to ground.
Go to Step 27.
No
Go to the next step.
13
INSPECT FRONT DOOR SPEAKER (RH) CIRCUIT FOR SHORT TO POWER SUPPLY
•  Verify that the following connectors are disconnected.
―  Tuner and amp unit (TAU)
―  Front door speaker (RH)
―  Tweeter (RH)
•  Connect the negative battery cable.
•  Switch the ignition ON (engine off or on).
•  Measure the voltage at the following terminals (wiring harness-side).
―  Front door speaker (RH) terminal C
―  Front door speaker (RH) terminal B
•  Is the voltage 0 V?
Yes
Go to the next step.
No
Refer to the wiring diagram and verify if there is a common connector between the following terminals.
•  Tuner and amp unit (TAU) terminal 2D and front door speaker (RH) terminal C
•  Tuner and amp unit (TAU) terminal 2F and front door speaker (RH) terminal B
•  Tuner and amp unit (TAU) terminal 2D and tweeter (RH) terminal B
•  Tuner and amp unit (TAU) terminal 2F and tweeter (RH) terminal A
If there is a common connector:
•  Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for short to power supply to determine the malfunctioning location.
•  Repair or replace the malfunctioning location.
If there is no common connector:
•  Repair or replace the wiring harness which is shorted to the power supply.
Go to Step 27.
14
INSPECT FRONT DOOR SPEAKER (RH)
•  Inspect the front door speaker (RH).
•  Is the front door speaker (RH) normal?
Yes
Go to the next step.
No
Replace the front door speaker (RH), then go to Step 27.
(See FRONT DOOR SPEAKER REMOVAL/INSTALLATION.)
15
INSPECT TWEETER (RH)
•  Inspect the tweeter (RH).
•  Is the tweeter (RH) normal?
Yes
Go to Step 27.
No
Replace the tweeter (RH), then go to Step 27.
(See TWEETER REMOVAL/INSTALLATION.)
16
INSPECT TUNER AND AMP UNIT (TAU) CONNECTOR CONDITION
•  Switch the ignition off.
•  Disconnect the negative battery cable.
•  Disconnect the tuner and amp unit (TAU) connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 27.
17
INSPECT REAR DOOR SPEAKER (LH) CONNECTOR CONDITION
•  Disconnect the rear door speaker (LH) connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 27.
18
INSPECT REAR DOOR SPEAKER (LH) CIRCUIT FOR SHORT TO GROUND
•  Verify that the tuner and amp unit (TAU) and rear door speaker (LH) connectors are disconnected.
•  Inspect for continuity between the following terminals (wiring harness-side) and body ground.
―  Rear door speaker (LH) terminal C
―  Rear door speaker (LH) terminal B
•  Is there continuity?
Yes
Refer to the wiring diagram and verify if there is a common connector between the following terminals.
•  Tuner and amp unit (TAU) terminal 2S and rear door speaker (LH) terminal C
•  Tuner and amp unit (TAU) terminal 2U and rear door speaker (LH) terminal B
If there is a common connector:
•  Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for short to ground to determine the malfunctioning location.
•  Repair or replace the malfunctioning location.
If there is no common connector:
•  Repair or replace the wiring harness which is shorted to ground.
Go to Step 27.
No
Go to the next step.
19
INSPECT REAR DOOR SPEAKER (LH) CIRCUIT FOR SHORT TO POWER SUPPLY
•  Verify that the tuner and amp unit (TAU) and rear door speaker (LH) connectors are disconnected.
•  Connect the negative battery cable.
•  Switch the ignition ON (engine off or on).
•  Measure the voltage at the following terminals (wiring harness-side).
―  Rear door speaker (LH) terminal C
―  Rear door speaker (LH) terminal B
•  Is the voltage 0 V?
Yes
Go to the next step.
No
Refer to the wiring diagram and verify if there is a common connector between the following terminals.
•  Tuner and amp unit (TAU) terminal 2S and rear door speaker (LH) terminal C
•  Tuner and amp unit (TAU) terminal 2U and rear door speaker (LH) terminal B
If there is a common connector:
•  Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for short to power supply to determine the malfunctioning location.
•  Repair or replace the malfunctioning location.
If there is no common connector:
•  Repair or replace the wiring harness which is shorted to the power supply.
Go to Step 27.
20
INSPECT REAR DOOR SPEAKER (LH)
•  Inspect the rear door speaker (LH).
•  Is the rear door speaker (LH) normal?
Yes
Go to Step 27.
No
Replace the rear door speaker (LH), then go to Step 27.
(See REAR DOOR SPEAKER REMOVAL/INSTALLATION.)
21
INSPECT TUNER AND AMP UNIT (TAU) CONNECTOR CONDITION
•  Switch the ignition off.
•  Disconnect the negative battery cable.
•  Disconnect the tuner and amp unit (TAU) connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 27.
22
INSPECT REAR DOOR SPEAKER (RH) CONNECTOR CONDITION
•  Disconnect the rear door speaker (RH) connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 27.
23
INSPECT REAR DOOR SPEAKER (RH) CIRCUIT FOR SHORT TO GROUND
•  Verify that the tuner and amp unit (TAU) and rear door speaker (RH) connectors are disconnected.
•  Inspect for continuity between the following terminals (wiring harness-side) and body ground.
―  Rear door speaker (RH) terminal C
―  Rear door speaker (RH) terminal B
•  Is there continuity?
Yes
Refer to the wiring diagram and verify if there is a common connector between the following terminals.
•  Tuner and amp unit (TAU) terminal 2V and rear door speaker (RH) terminal C
•  Tuner and amp unit (TAU) terminal 2X and rear door speaker (RH) terminal B
If there is a common connector:
•  Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for short to ground to determine the malfunctioning location.
•  Repair or replace the malfunctioning location.
If there is no common connector:
•  Repair or replace the wiring harness which is shorted to ground.
Go to Step 27.
No
Go to the next step.
24
INSPECT REAR DOOR SPEAKER (RH) CIRCUIT FOR SHORT TO POWER SUPPLY
•  Verify that the tuner and amp unit (TAU) and rear door speaker (RH) connectors are disconnected.
•  Connect the negative battery cable.
•  Switch the ignition ON (engine off or on).
•  Measure the voltage at the following terminals (wiring harness-side).
―  Rear door speaker (RH) terminal C
―  Rear door speaker (RH) terminal B
•  Is the voltage 0 V?
Yes
Go to the next step.
No
Refer to the wiring diagram and verify if there is a common connector between the following terminals.
•  Tuner and amp unit (TAU) terminal 2V and rear door speaker (RH) terminal C
•  Tuner and amp unit (TAU) terminal 2X and rear door speaker (RH) terminal B
If there is a common connector:
•  Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for short to power supply to determine the malfunctioning location.
•  Repair or replace the malfunctioning location.
If there is no common connector:
•  Repair or replace the wiring harness which is shorted to the power supply.
Go to Step 27.
25
INSPECT REAR DOOR SPEAKER (RH)
•  Inspect the rear door speaker (RH).
•  Is the rear door speaker (RH) normal?
Yes
Go to Step 27.
No
Replace the rear door speaker (RH), then go to Step 27.
(See REAR DOOR SPEAKER REMOVAL/INSTALLATION.)
26
INSPECT TUNER AND AMP UNIT (TAU) CONNECTOR CONDITION
•  Switch the ignition off.
•  Disconnect the negative battery cable.
•  Disconnect the tuner and amp unit (TAU) connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to the next step.
27
VERIFY THAT REPAIRS HAVE BEEN COMPLETED
•  Always reconnect all disconnected connectors.
•  Connect the negative battery cable.
•  Clear the DTC for the connectivity master unit (CMU) using the M-MDS.
•  Switch the ignition ON (engine off or on) and wait for 7 s or more.
•  Retrieve the connectivity master unit (CMU) DTCs using the M-MDS.
•  Is the same DTC displayed?
Yes
Repeat the inspection from Step 1.
•  If the malfunction recurs, replace the tuner and amp unit (TAU).
Go to the next step.
No
Go to the next step.
28
VERIFY IF OTHER DTCs DISPLAYED
•  Are any other DTCs displayed?
Yes
Repair or replace the malfunctioning part according to the applicable DTC troubleshooting.
(See DTC TABLE [CONNECTIVITY MASTER UNIT].)
No
DTC troubleshooting completed.