PID/DATA MONITOR TABLE [EPS CONTROL MODULE]

id060230813400

Note
•  If the PID “STR_ANG” is inspected, perform the following procedure before inspecting.
1.  Switch the ignition to OFF, and maintain this condition for approx. 3 s.
2.  Set the vehicle wheels in the straight-ahead position.
3.  Switch the ignition ON (engine off or on).

—: Not applicable

Monitor item

Unit/Operation

Test condition

Specification (Reference)

Inspection item

M-MDS display
ECU_IN_TMP
°C, °F
This PID indicates temperature of board in EPS control module.
•  Replace the steering column.
ENG_RPM
RPM
This PID indicates engine speed.
•  Inspect the PCM.
MT_CURRENT
A
When not steered
Near 0 A
•  Replace the steering column.
Steered left
Changes to 0 A—negative
Steered right
Changes to 0 A—positive
OH_CR_C
Yes/No
Overheat protection control (complete) is operating
Yes
—
Overheat protection control (complete) is not operating
No
OH_CR_M
Yes/No
Overheat protection control (middle) is operating
Yes
—
Overheat protection control (middle) is not operating
No
OH_HIST_C
Yes/No
Before overheat protection control (complete) has operated
Yes
—
Before overheat protection control (complete) has not operated
No
OH_HIST_M
Yes/No
Before overheat protection control (middle) has operated
Yes
—
Before overheat protection control (middle) has not operated
No
OH_IG_CNT_C
—
The number of times the ignition is switched ON during the period from when overheat protection control (complete) is finished to the time the next overheat protection control (complete) is started
•  Displays a maximum number of 255 times in which the ignition is switched ON until the first overheat protection control (complete) is started.
•  During overheat protection control (complete), the number of times the ignition is switched ON is not counted, and 0 is displayed.
—
OH_IG_CNT_M
—
The number of times the ignition is switched ON during the period from when overheat protection control (middle) is finished to the time the next overheat protection control (middle) is started
•  Displays a maximum number of 255 times in which the ignition is switched ON until the first overheat protection control (middle) is started.
•  During overheat protection control (middle), the number of times the ignition is switched ON is not counted, and 0 is displayed.
—
STR_AB_EST
Note
•  The signal indicated in this item is a steering angle (estimated absolute angle).
°
Steering wheel position when vehicle wheels straight-ahead
0 °
•  Perform the DTC inspection for the PCM, DSC HU/CM, and EPS control module. If a DTC is displayed after performing the DTC inspection for the PCM, DSC HU/CM, and EPS control module, repair the malfunctioning part according to the applicable DTC troubleshooting.
•  After performing the DTC inspection, perform the following procedures:
―  Switch the ignition off and maintain condition for approx. 3 s.
―  Switch the ignition ON (engine off or on).
―  Set the vehicle wheels straight-ahead, then drive the vehicle straight at 20 km/h {12 mph} or more for 5 s or more.
―  Using the M-MDS, verify the STR_ANG_EST operation condition.
•  If an abnormal value is indicated after verifying the value of the STR_AB_EST ANG again, replace the steering column.
Steered left
Changes to 0 °—positive
Steered right
Changes to 0 °—negative
STR_ANG
Note
•  The signal indicated in this item is a steering angle (relative angle).
°
Steering wheel position when ignition is switched ON (engine off or on)
0 °
•  Perform the DTC inspection for the PCM, DSC HU/CM, and EPS control module. If a DTC is displayed after performing the DTC inspection for the PCM, DSC HU/CM, and EPS control module, repair the malfunctioning part according to the applicable DTC troubleshooting.
•  After performing the DTC inspection, perform the following procedures:
―  Switch the ignition off and maintain condition for approx. 3 s.
―  Set the vehicle wheels straight-ahead.
―  Switch the ignition ON (engine off or on).
―  Using the M-MDS, verify the STR_ANG operation condition.
•  If an abnormal value is indicated after verifying the value of the STR_ANG again, replace the steering column.
Steered left
Changes to 0 °—negative
Steered right
Changes to 0 °—positive
STR_ROT_SPD
°/s
Not steered
Near 0 °/s
•  Replace the steering column.
Steered
Changes according to steering speed
STR_TRQ_S_M
Nm
Not steered
Near 0 Nm
•  Replace the steering column.
Steered left
Changes to 0 Nm—positive
Steered right
Changes to 0 Nm—negative
STR_TRQ_S_S
Nm
Not steered
Near 0 Nm
•  Replace the steering column.
Steered left
Changes to 0 Nm—positive
Steered right
Changes to 0 Nm—negative
VPWR
V
This PID indicates power supply voltage for EPS control module.
•  Inspect the battery.
•  Inspect power supply circuit (ignition switch, IG1 relay, fuse etc.)
VSPD
KPH, MPH
This PID indicates vehicle speed.
•  Inspect the DSC HU/CM.