DTC P1794:00 [i-ELOOP]

id130201001700

Note

• To determine the malfunctioning part, proceed with the diagnostics from "Function Inspection Using M-MDS".

• If the capacitor (i-ELOOP) voltage is low after replacing the DC-DC converter (i-ELOOP), the i-ELOOP indicator light (green) flashes until the capacitor (i-ELOOP) voltage is approx. 9.5 V.

Details On DTCs

DESCRIPTION

Capacitor (i-ELOOP) system: Capacitor (i-ELOOP) malfunction

DETECTION CONDITION

Determination conditions

Capacitor (i-ELOOP) malfunction determined

•  Any one of the following conditions is met:

―  Capacitor (i-ELOOP) interrupt relay has a malfunction.

―  Capacitor (i-ELOOP) internal resistance exceeds the specification.

―  Capacitor (i-ELOOP) capacitance exceeds the specification.

―  Capacitor (i-ELOOP) voltage exceeds the specification.

―  Service plug is pulled out during vehicle travel.

Capacitor (i-ELOOP) deterioration determined

•  Any one of the following conditions is met:

―  Capacitor (i-ELOOP) internal resistance exceeds the specification.

―  Capacitor (i-ELOOP) capacitance is less than the specification.

Over-charge determined

•  Capacitor (i-ELOOP) voltage exceeds the specification.

Preconditions

•  Ignition switched ON

Drive cycle

•  1

Self test type

•  CMDTC self test, ODDTC self test

Sensor used

•  DC-DC converter (i-ELOOP)

FAIL-SAFE FUNCTION

•  Inhibits engine-stop by operating the i-stop function. (With i-stop)

•  Inhibits the i-ELOOP control.

•  Switches to bypass mode which shuts the capacitor (i-ELOOP) off.

VEHICLE STATUS WHEN DTCs ARE OUTPUT

•  Flashes i-stop warning light (amber). (With i-stop)

•  Illuminates i-ELOOP warning light (amber).

•  The following vehicle conditions differ depending on the type of malfunction

―  Charging system warning light turns on (DC-DC converter (i-ELOOP) turns on during over-charge determination)

―  Master warning light turns on (illumination during bypass mode by i-ELOOP)

POSSIBLE CAUSE

•  Engagement malfunction in capacitor (i-ELOOP), DC-DC converter (i-ELOOP)

•  Capacitor (i-ELOOP) malfunction

―  Capacitor (i-ELOOP) deterioration

―  Capacitor (i-ELOOP) interrupt relay malfunction

•  Generator overcharge (in this case, PCM detects DTC P2504:00)

•  DC-DC converter (i-ELOOP) malfunction

DESCRIPTION	Capacitor (i-ELOOP) system: Capacitor (i-ELOOP) malfunction
DETECTION CONDITION	Determination conditions	Capacitor (i-ELOOP) malfunction determined • Any one of the following conditions is met: ― Capacitor (i-ELOOP) interrupt relay has a malfunction. ― Capacitor (i-ELOOP) internal resistance exceeds the specification. ― Capacitor (i-ELOOP) capacitance exceeds the specification. ― Capacitor (i-ELOOP) voltage exceeds the specification. ― Service plug is pulled out during vehicle travel. Capacitor (i-ELOOP) deterioration determined • Any one of the following conditions is met: ― Capacitor (i-ELOOP) internal resistance exceeds the specification. ― Capacitor (i-ELOOP) capacitance is less than the specification. Over-charge determined • Capacitor (i-ELOOP) voltage exceeds the specification.
Preconditions	• Ignition switched ON
Drive cycle	• 1
Self test type	• CMDTC self test, ODDTC self test
Sensor used	• DC-DC converter (i-ELOOP)
FAIL-SAFE FUNCTION	• Inhibits engine-stop by operating the i-stop function. (With i-stop) • Inhibits the i-ELOOP control. • Switches to bypass mode which shuts the capacitor (i-ELOOP) off.
VEHICLE STATUS WHEN DTCs ARE OUTPUT	• Flashes i-stop warning light (amber). (With i-stop) • Illuminates i-ELOOP warning light (amber). • The following vehicle conditions differ depending on the type of malfunction ― Charging system warning light turns on (DC-DC converter (i-ELOOP) turns on during over-charge determination) ― Master warning light turns on (illumination during bypass mode by i-ELOOP)
POSSIBLE CAUSE	• Engagement malfunction in capacitor (i-ELOOP), DC-DC converter (i-ELOOP) • Capacitor (i-ELOOP) malfunction ― Capacitor (i-ELOOP) deterioration ― Capacitor (i-ELOOP) interrupt relay malfunction • Generator overcharge (in this case, PCM detects DTC P2504:00) • DC-DC converter (i-ELOOP) malfunction

System Wiring Diagram

• Not applicable

Function Explanation (DTC Detection Outline)

• The capacitor (i-ELOOP) can store generated electrical energy from the generator efficiently.

• The electrical energy stored during deceleration fuel-cut is used during driving and while the engine is stopped by i-stop, which reduces the power generating load on the generator and the amount of fuel consumption.

• If a malfunction occurs with the capacitor (i-ELOOP), constant charging takes place by operation of the bypass mode which could cause the fuel economy to worsen.

• In this diagnostic, the internal resistance/capacitance is calculated from the capacitor (i-ELOOP) voltage value and charge/discharge current value, and the DC-DC converter (i-ELOOP) determines that there is a malfunction in the battery-related parts by the internal resistance/capacitance/capacitor (i-ELOOP) voltage exceeding the specified value, and it stores a DTC.

Repeatability Verification Procedure

1. If the negative battery cable is disconnected and re-connected, perform the battery condition initial setting (i-stop setting) to complete the i-stop initial setting. (See BATTERY CONDITION INITIALIZATION SETTING (i-stop SETTING).)

2. Start the engine.(no electrical load)

3. Depress the accelerator pedal to increase the engine speed to 3,000 rpm.

4. Release the accelerator pedal to idle the engine.

5. Stop the engine.

6. Switch the ignition on and wait for 1 min.

7. Switch the ignition off and wait for 20 min.

8. Start the engine.(no electrical load)

9. Verify that Power Output (Normal) is displayed for the DC-DC converter (i-ELOOP) voltage reduction circuit operation status (PID: CONV_STAT) using the M-MDS data monitor function. (See PID/DATA MONITOR INSPECTION [i-ELOOP].)

― If Power Output (Normal) cannot be verified, verify that DTCs related to the capacitor are detected. (See DTC INSPECTION [i-ELOOP].) (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-G 1.3, SKYACTIV-G 1.5].) (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-D 1.5].)

• If DTCs are detected, repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [i-ELOOP].) (See DTC TABLE [SKYACTIV-G 1.3, SKYACTIV-G 1.5].) (See DTC TABLE [SKYACTIV-D 1.5].)

• If DTCs are not detected, wait for 30 min or more and then implement Step 9 in the repeatability verification procedure again.

PID Item/Simulation Item Used In Diagnosis

PID/DATA monitor item table

Item	Definition	Unit	Condition/Specification
CAP_SYS_10	Open circuit condition of the capacitor circuit	Off/On	• Capacitor (i-ELOOP) open circuit: On • Capacitor circuit is normal: Off
CAP_SYS_14	Capacitor (i-ELOOP) capacitance deterioration	Off/On	• Capacitor (i-ELOOP) capacitance status deteriorates: On • Capacitor (i-ELOOP) capacitance status is normal: Off
CAP_SYS_16	Capacitor (i-ELOOP) internal resistance deterioration	Off/On	• Internal resistance status in capacitor (i-ELOOP) deteriorates: On • Internal resistance status in capacitor (i-ELOOP) is normal: Off
CAP_SYS_17	Short circuit to ground malfunction in the capacitor (i-ELOOP)	Off/On	• Short circuit to ground in capacitor (i-ELOOP): On • No short circuit to ground in capacitor (i-ELOOP): Off

Function Inspection Using M-MDS

STEP

INSPECTION

RESULTS

ACTION

1

PURPOSE: VERIFY RELATED SERVICE INFORMATION AVAILABILITY

•  Verify related Service Information availability.

•  Is any related Service Information available?

Yes

Perform repair or diagnosis according to the available Service Information.

•  If the vehicle is not repaired, go to the next step.

No

Go to the next step.

2

PURPOSE: VERIFY IF DIAGNOSTIC RESULT IS AFFECTED BY DTC RELATED TO GENERATOR OVERCHARGE

•  Switch the ignition off, then ON (engine off).

•  Perform the PCM DTC inspection using the M-MDS.
(See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-G 1.3, SKYACTIV-G 1.5].)

(See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-D 1.5].)

•  Is the DTC P2504:00 also present?

Yes

Go to the applicable DTC inspection.

(See DTC P2504:00 [SKYACTIV-G 1.3, SKYACTIV-G 1.5].)

(See DTC P2504:00 [SKYACTIV-D 1.5].)

No

Go to the next step.

3

PURPOSE: VERIFY IF POWER SUPPLY IS AFFECTED BY DTC RELATED TO DC-DC CONVERTER (i-ELOOP)

•  Perform the DC-DC converter (i-ELOOP) DTC inspection using the M-MDS.
(See DTC INSPECTION [i-ELOOP].)

•  Are any DTCs present?

Yes

DTC U3000:49 is displayed:

•  Go to the next step.

Any other DTCs are displayed:

•  Go to the applicable DTC inspection.
(See DTC TABLE [i-ELOOP].)

No

Go to the troubleshooting procedure to perform the procedure from Step 1.

4

VERIFY THE OPEN CIRCUIT CONDITION OF THE CAPACITOR CUIRCUIT

•  Access the CAP_SYS10 PID using the M-MDS.
(See PID/DATA MONITOR INSPECTION [i-ELOOP].)

•  Is the CAP_SYS10 PID value off?

Yes

Reconnect the service plug, then go to the next Step.

No

Go to the next step.

5

PURPOSE: DETERMINE IF THE MALFUNCTION IS CAUSED BY CAPACITOR (i-ELOOP) BY VERIFYING THE PID RELATED TO THE CAPACITOR (i-ELOOP)

•  Access the following DC-DC converter (i-ELOOP) PIDs using the M-MDS
(See PID/DATA MONITOR INSPECTION [i-ELOOP].)

―  CAP_SYS_10

―  CAP_SYS_14

―  CAP_SYS_16

―  CAP_SYS_17

•  Are all of the PID item “CAP_SYS10, CAP_SYS_14, CAP_SYS_16, CAP_SYS_17” values off?

Yes

Replace the DC-DC converter (i-ELOOP).

(See DC-DC CONVERTER (i-ELOOP) REMOVAL/INSTALLATION [WITH i-ELOOP (SKYACTIV-G 1.3, SKYACTIV-G 1.5)].)

(See DC-DC CONVERTER (i-ELOOP) REMOVAL/INSTALLATION [WITH i-ELOOP (SKYACTIV-D 1.5)].)

Go to the troubleshooting procedure to perform the procedure from Step 2.

No

Replace the capacitor (i-ELOOP).

(See CAPACITOR (i-ELOOP) REMOVAL/INSTALLATION [i-ELOOP].)

Go to the troubleshooting procedure to perform the procedure from Step 2.

STEP	INSPECTION	RESULTS	ACTION
1	PURPOSE: VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
No	Go to the next step.
2	PURPOSE: VERIFY IF DIAGNOSTIC RESULT IS AFFECTED BY DTC RELATED TO GENERATOR OVERCHARGE • Switch the ignition off, then ON (engine off). • Perform the PCM DTC inspection using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-G 1.3, SKYACTIV-G 1.5].) (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-D 1.5].) • Is the DTC P2504:00 also present?	Yes	Go to the applicable DTC inspection. (See DTC P2504:00 [SKYACTIV-G 1.3, SKYACTIV-G 1.5].) (See DTC P2504:00 [SKYACTIV-D 1.5].)
No	Go to the next step.
3	PURPOSE: VERIFY IF POWER SUPPLY IS AFFECTED BY DTC RELATED TO DC-DC CONVERTER (i-ELOOP) • Perform the DC-DC converter (i-ELOOP) DTC inspection using the M-MDS. (See DTC INSPECTION [i-ELOOP].) • Are any DTCs present?	Yes	DTC U3000:49 is displayed: • Go to the next step. Any other DTCs are displayed: • Go to the applicable DTC inspection. (See DTC TABLE [i-ELOOP].)
No	Go to the troubleshooting procedure to perform the procedure from Step 1.
4	VERIFY THE OPEN CIRCUIT CONDITION OF THE CAPACITOR CUIRCUIT • Access the CAP_SYS10 PID using the M-MDS. (See PID/DATA MONITOR INSPECTION [i-ELOOP].) • Is the CAP_SYS10 PID value off?	Yes	Reconnect the service plug, then go to the next Step.
No	Go to the next step.
5	PURPOSE: DETERMINE IF THE MALFUNCTION IS CAUSED BY CAPACITOR (i-ELOOP) BY VERIFYING THE PID RELATED TO THE CAPACITOR (i-ELOOP) • Access the following DC-DC converter (i-ELOOP) PIDs using the M-MDS (See PID/DATA MONITOR INSPECTION [i-ELOOP].) ― CAP_SYS_10 ― CAP_SYS_14 ― CAP_SYS_16 ― CAP_SYS_17 • Are all of the PID item “CAP_SYS10, CAP_SYS_14, CAP_SYS_16, CAP_SYS_17” values off?	Yes	Replace the DC-DC converter (i-ELOOP). (See DC-DC CONVERTER (i-ELOOP) REMOVAL/INSTALLATION [WITH i-ELOOP (SKYACTIV-G 1.3, SKYACTIV-G 1.5)].) (See DC-DC CONVERTER (i-ELOOP) REMOVAL/INSTALLATION [WITH i-ELOOP (SKYACTIV-D 1.5)].) Go to the troubleshooting procedure to perform the procedure from Step 2.
No	Replace the capacitor (i-ELOOP). (See CAPACITOR (i-ELOOP) REMOVAL/INSTALLATION [i-ELOOP].) Go to the troubleshooting procedure to perform the procedure from Step 2.

Troubleshooting Diagnostic Procedure

Intention of troubleshooting procedure

• Step 1

― Verify the engagement condition of each part.

• Step 2—3

― Verify that the primary malfunction is resolved and there are no other malfunctions.

STEP

INSPECTION

RESULTS

ACTION

1

PURPOSE: VERIFY IF MALFUNCTION CAUSED BY ENGAGEMENT MALFUNCTION OF EACH PART

•  Switch the ignition off.

•  Disconnect the negative battery cable.
(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION.)

•  Remove the service plug.
(See SERVICE PLUG DISCONNECTION/CONNECTION [i-ELOOP].)

•  Verify that the following parts are engaged correctly.

―  DC-DC converter (i-ELOOP)
(See DC-DC CONVERTER (i-ELOOP) REMOVAL/INSTALLATION [WITH i-ELOOP (SKYACTIV-G 1.3, SKYACTIV-G 1.5)].)

(See DC-DC CONVERTER (i-ELOOP) REMOVAL/INSTALLATION [WITH i-ELOOP (SKYACTIV-D 1.5)].)

―  Capacitor (i-ELOOP)
(See CAPACITOR (i-ELOOP) REMOVAL/INSTALLATION [i-ELOOP].)

•  Is the engagement condition of each part normal?

Yes

Go to the next step.

No

Tighten the DC-DC converter (i-ELOOP) or capacitor (i-ELOOP) properly, then go to the next step.

2

PURPOSE: VERIFICATION OF VEHICLE REPAIR COMPLETION

•  Always reconnect all disconnected connectors.

•  Reinstall the service plug.
(See SERVICE PLUG DISCONNECTION/CONNECTION [i-ELOOP].)

•  Reconnect the negative battery cable.
(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION.)

•  Start the engine and leave for 100 s or more.

•  Clear the DTC for the DC-DC converter (i-ELOOP) using the M-MDS.
(See CLEARING DTC [i-ELOOP].)

•  Implement the repeatability verification procedure.
(See Repeatability Verification Procedure.)

•  Retrieve the DC-DC converter (i-ELOOP) DTCs using the M-MDS.
(See DTC INSPECTION [i-ELOOP].)

•  Is the same DTC present?

Yes

Replace the capacitor (i-ELOOP) and verify that the repairs have been completed in Step 2.

(See CAPACITOR (i-ELOOP) REMOVAL/INSTALLATION [i-ELOOP].)

•  If the malfunction recurs, replace the DC-DC converter (i-ELOOP).
(See DC-DC CONVERTER (i-ELOOP) REMOVAL/INSTALLATION [WITH i-ELOOP (SKYACTIV-G 1.3, SKYACTIV-G 1.5)].)

(See DC-DC CONVERTER (i-ELOOP) REMOVAL/INSTALLATION [WITH i-ELOOP (SKYACTIV-D 1.5)].)

―  Start the engine and leave for 100 s or more.

―  Clear the DTC for the DC-DC converter (i-ELOOP) using the M-MDS.
(See CLEARING DTC [i-ELOOP].)

Go to the next step.

No

Go to the next step.

3

PURPOSE: VERIFY IF THERE IS ANY OTHER MALFUNCTION

•  Is any other DTC or pending code stored?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [i-ELOOP].)

No

DTC troubleshooting completed.

STEP	INSPECTION	RESULTS	ACTION
1	PURPOSE: VERIFY IF MALFUNCTION CAUSED BY ENGAGEMENT MALFUNCTION OF EACH PART • Switch the ignition off. • Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION.) • Remove the service plug. (See SERVICE PLUG DISCONNECTION/CONNECTION [i-ELOOP].) • Verify that the following parts are engaged correctly. ― DC-DC converter (i-ELOOP) (See DC-DC CONVERTER (i-ELOOP) REMOVAL/INSTALLATION [WITH i-ELOOP (SKYACTIV-G 1.3, SKYACTIV-G 1.5)].) (See DC-DC CONVERTER (i-ELOOP) REMOVAL/INSTALLATION [WITH i-ELOOP (SKYACTIV-D 1.5)].) ― Capacitor (i-ELOOP) (See CAPACITOR (i-ELOOP) REMOVAL/INSTALLATION [i-ELOOP].) • Is the engagement condition of each part normal?	Yes	Go to the next step.
1		No	Tighten the DC-DC converter (i-ELOOP) or capacitor (i-ELOOP) properly, then go to the next step.
2	PURPOSE: VERIFICATION OF VEHICLE REPAIR COMPLETION • Always reconnect all disconnected connectors. • Reinstall the service plug. (See SERVICE PLUG DISCONNECTION/CONNECTION [i-ELOOP].) • Reconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION.) • Start the engine and leave for 100 s or more. • Clear the DTC for the DC-DC converter (i-ELOOP) using the M-MDS. (See CLEARING DTC [i-ELOOP].) • Implement the repeatability verification procedure. (See Repeatability Verification Procedure.) • Retrieve the DC-DC converter (i-ELOOP) DTCs using the M-MDS. (See DTC INSPECTION [i-ELOOP].) • Is the same DTC present?	Yes	Replace the capacitor (i-ELOOP) and verify that the repairs have been completed in Step 2. (See CAPACITOR (i-ELOOP) REMOVAL/INSTALLATION [i-ELOOP].) • If the malfunction recurs, replace the DC-DC converter (i-ELOOP). (See DC-DC CONVERTER (i-ELOOP) REMOVAL/INSTALLATION [WITH i-ELOOP (SKYACTIV-G 1.3, SKYACTIV-G 1.5)].) (See DC-DC CONVERTER (i-ELOOP) REMOVAL/INSTALLATION [WITH i-ELOOP (SKYACTIV-D 1.5)].) ― Start the engine and leave for 100 s or more. ― Clear the DTC for the DC-DC converter (i-ELOOP) using the M-MDS. (See CLEARING DTC [i-ELOOP].) Go to the next step.
2		No	Go to the next step.
3	PURPOSE: VERIFY IF THERE IS ANY OTHER MALFUNCTION • Is any other DTC or pending code stored?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [i-ELOOP].)
3		No	DTC troubleshooting completed.